- Home
- Networking
- CCNP Switching 642-813
6.
R1 and R2 are switches that communicate via VTP. What is the default VTP advertisement
intervals in Catalyst switches that are in server or client mode?
- A.30 seconds
- B.5 minutes
- C.1 minute
- D.10 seconds
- E.5 seconds
- F.None of the other alternatives apply
- Answer & Explanation
- Report
Answer : [B]
Explanation :
Explanation :
| Periodic ( default is 5 minutes) VTP advertisements are sent out each trunk port with the multicast destination MAC address 01-00-0C-CC-CC-CC. VTP advertisements contain the following configuration information: VLAN IDs (ISL and 802.1Q) Emulated LAN names ( ATM LANE ) 802.10 SAID values (FDDI) VTP domain name VTP configuration revision number VLAN configuration, including the maximum transmission unit (MTU) size for each VLAN Frame format. |
7.
You want to configure switch R1 to propagate VLAN information across the Company network
using VTP. What must be configured on a Cisco switch in order to advertise VLAN information?
- A.VVTP mode.
- B.VTP password.
- C.VTP revision number.
- D.VTP pruning.
- E.VTP domain name.
- F.None of the other alternatives apply.
- Answer & Explanation
- Report
Answer : [E]
Explanation :
Explanation :
|
If the switch being installed is the first switch in the network, the management domain will need to
be created. However, if the network has other switches running VTP, then the new switch will join
an existing management domain. Verify the name of the management domain. If the management
domain has been secured, verify and configure the password for the domain. To create a management domain or to add a switch to a management domain, use the vtp domain command in the global configuration mode or VLAN configuration mode. Switch( config)# vtp domain name Switch(vlan)# vtp domain |
8.
The Company switches have all been upgraded to use VTP version 2. What are two benefits
provided in VTP Version 2 that are not available in VTP Version 1? (Select two)
- A.VTP version 2 supports Token Ring VLANs
- B.VTP version 2 allows VLAN consistency checks.
- C.VTP version 2 allows active redundant links when used with spanning tree
- D.VTP version 2 reduces the amount of configuration necessary.
- E.VTP version 2 saves VLAN configuration memory.
- Answer & Explanation
- Report
Answer : [A, B]
Explanation :
Explanation :
| If you use VTP in your network, you must decide whether to use VTP version1 or version2. |
9.
VTP is configured on switch R1. Which of the following features were added in VTP version 2 that
were not previously supported in VTP version 1? (Select two)
- A.Supports Token Ring VLANs..
- B.Allows VLAN consistency checks..
- C.Saves VLAN configuration memory..
- D.Reduces the amount of configuration necessary.
- E.Allows active redundant links when used with spanning tree.
- Answer & Explanation
- Report
Answer : [A, B]
Explanation :
Explanation :
| VTP Version 2 includes the following improvements: Token Ring VLAN support, TLV support, transparent mode, and Consistency checks. |
10.
The Company switches are configured to use VTP. What's true about the VLAN trunking protocol
(VTP)? (Select two)
- A.VTP messages will not be forwarded over nontrunk links.
- B.VTP domain names need to be identical. However, case doesn't matter.
- C.A VTP enabled device which receives multiple advertisements will ignore advertisements with higher configuration revision numbers.
- D.A device in "transparent" VTP v.1 mode will not forward VTP messages.
- E.VTP pruning allows switches to prune VLANs that do not have any active ports associated with them.
- Answer & Explanation
- Report
Answer : [A, D]
Explanation :
Explanation :
| VTP messages are only transmitted across trunk links. If the receiving switch is in transparent mode, the configuration is not changed. Switches in transparent mode do not participate in VTP. If you make VTP or VLAN configuration changes on a switch in transparent mode, the changes are not propagated to the other switches in the network. |
|
|
||||||||||||||||||||||||||||
